D Series - Precision Heavy Duty Flexible Coupling  
  
 Configure a Product
     
   Download PDF
     
 Download Adobe Reader
   
• Convert Matrix to Metric Information
   
Part No.
Thru Bore
 D L E F G Clamp
 Set
Inch
+.000
-.010 		Inch
±.015		 Inch
±.005

Note
2 		Inch
±.015		 Inch
±.005		 (screw) Inch
(torque) LB.IN.

Notes
7-11
DTOOO050
 .495 .75 .200 .350 0.092 1-72
5 		4-40
5
DTOOO062
 .620 .87 .220 .430 .100 2-56
7 		6-32
10
DTOOO075
 .745 1.00 .250 .500 .125 4-40
18 		8-32
20
DTOOO100
 .995 1.50 .420 .650 .200 6-32
34 		10-24
36
DTOOO125
 1.240 2.00 .420 1.150 .200 8-32
59 		10-24
36
DTOOO150
 1.485 2.37 .515 1.34 .240 10-24
77 		1/4-20
87
DTOOO162
 1.610 2.50 515 1.47 .240 1/4-20
77 		1/4-20
87
DTOOO175
 1.735 2.75 .515 1.60 .240 1/4-20
77 		1/4-20
87
DTOOO200
 1.970 3.00 .515 1.97 .240 1/4-20
200 		1/4-20
87
DTOOO225
 2.220 3.25 .515 2.22 .240 1/4-20
200 		1/4-20
87
            
Part No.
Thru Bore
 B1 Bore B2 Bore Static Torque Torsional Stiffness Inertia Mass Misalignment
(see definitions)
Inch
+.001
-.000

Notes
1,2,3		 MM
+.025
-.000

Notes
1,2,3		 Inch
+.001
-.000

Notes
1,2,3		 MM
+.025
-.000

Notes
1,2,3

LB.IN

Notes
4,5
MIN /
LB.IN

Note
5
10-3
Ib.in.2

Note
6

Ib.

Note
6		 Angular
Offset Degrees		 Parallel
Off Set
Inch

 Axial
Motion
Inch
DTOOO050
     0.093 2.5         3° 0.007 ±.005
0.120 3 0.120 3        
0.125 3 0.125 3        
0.156 4 0.156 4 7.8 47.81 0.424 0.012
0.187 5 0.187 5 6.3 53.22 0.418 0.011
DTOOO062
     0.120 3         4° 0.010 ±.005
    0.125 3        
0.156 4 0.156 4 15 23.42 1.109 0.021
0.187 5 0.187 5 14 25.20 1.104 0.020
0.250 6 0.250 6 12 32.51 1.087 0.019
DTOOO075
     0.120 3         5° 0.015 ±.010
    0.125 3        
    0.156 4        
0.187 5 0.187 5 41 10.66 2.732 0.036
0.250 6 0.250 6 35 14.16 2.713 0.034
0.312 8 0.312 8 28 23.13 2.674 0.033
DTOOO100
     0.125 3         7° 0.030 ±.020
    0.156 4        
    0.187 5        
0.250 6 0.250 6 76 4.43 13.18 0.098
0.312 8 0.312 8 73 5.35 13.12 0.095
0.375 10 0.375 10 67 6.47 13.01 0.092
DTOOO125
     0.187 5         10° 0.040 ±.025
    0.250 6        
0.312 8 0.312 8 108 2.63 42.21 0.199
0.375 10 0.375 10 97 3.16 41.96 0.193
0.437 11-12 0.437 11-12 91 3.89 41.56 0.186
0.500 14 0.500 14 77 5.27 40.92 0.178
DTOOO150
     0.250 6         10° 0.050 ±.020
    0.312 8        
0.375 10 0.375 10 186 1.82 103.6 0.338
0.437 12 0.437 12 175 2.07 103.1 0.331
0.500 14 0.500 14 168 2.44 102.4 0.322
0.625 16 0.625 16 156 3.31 100.9 0.308
Part No.
Thru Bore
 B1 Bore B2 Bore Static Torque Torsional Stiffness Inertia Mass Misalignment
(see definitions)
Inch
+.001
-.000

Notes
1,2,3		 MM
+.025
-.000

Notes
1,2,3		 Inch
+.001
-.000

Notes
1,2,3		 MM
+.025
-.000

Notes
1,2,3

LB.IN

Notes
4,5
MIN /
LB.IN

Note
5
10-3
Ib.in.2

Note
6

Ib.

Note
6		 Angular
Offset Degrees		 Parallel
Off Set
Inch

 Axial
Motion
Inch
DTOOO162
     0.250 6         10° 0.050 ±.020
    0.312 8        
    0.375 10        
0.437 12 0.437 12 258 1.53 148.7 0.410
0.500 14 0.500 14 241 2.04 147.8 0.399
0.625 16 0.625 16 230 2.53 146.1 0.384
0.687 18 0.687 18 218 3.11 144.2 0.370
DTOOO175
     0.312 8         10° 0.055 ±.025
    0.375 10        
    0.437 12        
0.500 14 0.500 14 319 1.22 220.5 0.512
0.625 16 0.625 16 304 1.50 218.4 0.494
0.687 18 0.687 18 259 1.80 216.0 0.478
0.750 20 0.750 20 216 2.36 212.7 0.461
DTOOO200
     0.375 10         10° 0.060 ±.030
    0.437 12        
    0.500 14        
0.625 16 0.625 16 367 0.95 413.3 0.729
0.687 18 0.687 18 355 1.25 410.2 0.710
0.750 20 0.750 20 337 1.45 406.2 0.689
0.875 22 0.875 22 308 1.90 399.6 0.660
DTOOO225
     0.437 12         10° 0.060 ±.030
    0.500 14        
0.625 16 0.625 16 560 0.75 727.6 1.03
0.687 18 0.687 18 538 0.85 723.1 1.01
0.750 20 0.750 20 505 0.87 720.8 1.00
0.875 22 0.875 22 464 0.89 714.2 .970
1.000 24-25 1.000 24-25 421 0.92 702.2 .927
  
  1. All THRU BORE couplings have an inside relief so the shafts will not touch the beams at the maximum misalignment. All bores shown are thru bores.
  2. All LIMITED BORE couplings have the same OD have the same ID. The torque, stiffness and inertia are the same for all bores. When the bores are in blue, the maximum shaft penetration is E depth. When one bore is in white it can extend into the flexible area. Torque and wind-up is shown in blue.
  3. Any B1 may be combined with any B2. The smallest B2 bores cannot be duplicated in the B1 column where they are not already shown.
  4. Static torque is the maximum torque rating for each B1 bore. The correct dynamic torque safety factor should be determined by the customer in accordance with fast reversals acceleration, deceleration, sudden stops, etc.
  5. Torque and torsional stiffness ratings are at maximum misalignment, not in a straight line.
  6. Mass and inertia are calculated with the customers required B1 bore and the smallest B2 bore shown.
  7. Set screws are 120° apart. All screws are hex socket steel with black oxide finish. The torques are the screw manufacturers maximum ratings.
  8. Coupling material is 2024-T3.51 QQA225/6 aluminum with MIL A8625F Type II black anodize.
  9. Nickel plated couplings for added corrosion resistance are available for all Rocom couplings.
  10. G10 phenolic inserts for thermal and electrical isolation are available for all Rocom couplings.
  11. Clamps are an integral part of the coupling.
  12. Follow the installation procedures to ensure infinite life.
  13. TEST BEFORE YOU BUY. Rocom will furnish samples at no charge for all new OEM designs or for comparative evaluation.

Home   |   About ROCOM   |   Our Products   |   Coupling Design   |   Customer Support   |   Request A Quote   |   Contact Us   |   Site Map   |   Privacy
© Rocom Corporation. All rights reserved.
5957 Engineer Drive, Huntington Beach, California 92649 (714) 891-9922 or (800) 952-FLEX Fax (714) 891-2121 Email: Our Sales Department